Collier County HVAC

Leer esta página en español · Ler esta página em português

HomeFlow now handles heating and air conditioning across Collier County, from Gulf-front towers in Naples and on Marco Island to acreage homes in Golden Gate Estates and farm properties around Immokalee.

HVAC Services in Collier County

Residential

AC repair, heat pump replacement, ductless systems and duct work for houses and condos across the county.

Commercial

Rooftop units, VRF, refrigeration and kitchen ventilation for offices, shops, restaurants and ag buildings.

Maintenance

Scheduled service for full-time homes, seasonal homes that sit empty all summer and commercial buildings.

New Construction

Load calculations, duct design and leakage testing for new homes in Ave Maria, the Estates and beyond.

Heating and air conditioning across Collier County

Collier County covers a lot of ground, and the air conditioning work changes with it. A condo on Gulf Shore Boulevard, a block house in Golden Gate City, a new build in Ave Maria and a stilt home in Everglades City all need cooling nine months of the year, but the equipment, the access and the problems are very different.

HomeFlow, the plumbing company many Collier homeowners already know, now handles heating and air conditioning too. We repair and replace central air conditioners, heat pumps, air handlers and ductless mini-splits. We repair, seal and replace ductwork, set up thermostats and zoning, clear condensate drains, and add dehumidifiers and air quality equipment. For businesses we work on rooftop units, split and packaged systems, VRF, kitchen make-up air, walk-in coolers and maintenance agreements.

This page is the county overview. It covers how permits split up, what we see in each part of Collier, and how to get service. To book anything, call (239) 518-4198 or send the details through our service request form.

Which building department permits your AC changeout

Replacing an air conditioner or heat pump generally needs a mechanical permit in Collier, and new systems always do. Which office issues it depends on where the parcel sits, not the city on your mailing address. Plenty of homes with a Naples address are in unincorporated Collier County.

  • Collier County Growth Management handles unincorporated Collier, which is most of the county: North Naples, East Naples, Golden Gate City, Golden Gate Estates, Orangetree, Immokalee and Ave Maria.
  • The City of Naples Building Division covers work inside city limits, including Old Naples, Port Royal and Aqualane Shores.
  • The City of Marco Island runs its own building department for everything on the island.
  • Everglades City contracts with the county for permits and inspections, so mechanical permits there go through Collier County.

We check the parcel record before filing, because a permit filed with the wrong office gets bounced and the inspection waits. Skipping the permit on a changeout can come back to bite you during a home sale, an insurance claim or a manufacturer warranty request, so we pull it as part of the job.

Condo towers in Naples and on Marco Island

The Gulf side of the county is lined with mid-rise and high-rise condos, and cooling a unit in a tower is its own kind of job. Equipment might sit in a closet inside the unit, on a balcony, on the roof or in a mechanical room several floors away. Some older buildings use water-source heat pumps tied to a central cooling tower, which means part of the system belongs to the association and part belongs to you.

Before we start in a condo

  • We read what the association documents say about who owns the condenser, the air handler, the line set and the drain.
  • We confirm the building’s contractor rules, insurance paperwork and allowed work hours with management.
  • For roof or balcony equipment, we plan the lift. Some replacements need an elevator reservation, a hoist or a crane, and that has to be booked ahead.
  • We check the shared condensate drain. A clog in a building drain riser can back up into several units at once.

Florida’s milestone inspection law, passed after the 2021 Surfside collapse, has many older Collier buildings planning big projects, and roof work often means rooftop condensers have to be disconnected, lifted and reset. If your building is planning a reroof, it is a good time to look at the age of the units up there.

Salt air on the coast

Within a mile or so of the Gulf, salt spray settles on everything, and outdoor condenser coils take it hard. The thin aluminum fins corrode, the coil loses its ability to shed heat, and eventually it starts leaking refrigerant. Units facing the water on Marco, along Vanderbilt Beach and in Park Shore often show it years before a unit a few miles inland.

For coastal homes we look at coils with factory corrosion protection, coated fins, stainless hardware and sealed electrical connections. Rinsing the outdoor coil gently with fresh water every month or so helps a lot. Pressure washing does more harm than good, because it flattens fins.

Golden Gate City’s block homes

Golden Gate City was laid out in the 1960s, and much of it was built over the next couple of decades as concrete block ranch homes and duplexes. Most have a central system with the air handler in the garage, a utility closet or the attic, and ducts made of duct board or flex duct running through a hot attic.

A lot of what we find there is age. Original duct board with failed tape, a return grille pulling air from the attic, a condenser on its third replacement sitting on a cracked pad, or a system that still runs on R-22. R-22 has not been produced in the United States since 2020, so a leak on one of those systems usually turns into a replacement conversation.

Duplexes and rentals bring their own issues: two systems side by side, tenants who never change filters, and owners who need a straight answer on repair versus replace.

Golden Gate Estates and Orangetree acreage

Out in the Estates, homes sit on lots of an acre or more, many on private wells and septic, with long driveways, detached garages and workshops. That changes HVAC work in a few ways.

  • Lightning and power surges are a regular cause of failed boards, contactors and compressors out here. A surge protector at the condenser disconnect is cheap protection.
  • Many owners run a standby generator. If you want the AC on generator power after a storm, the system has to be sized and wired for it, and a soft start kit on the compressor can help a smaller generator handle the load.
  • Detached garages, workshops, guest suites and converted barns are good candidates for ductless mini-splits instead of running ducts across the property.
  • Condensate drains often dump right next to the slab. On a lot with a high water table in the rainy season, routing that water away from the foundation matters.

Orangetree and the newer communities along Immokalee Road and Oil Well Road mix older Estates homes with builder subdivisions, so we see everything from 1980s systems on acreage to recent installs that need their first real service.

Residential AC repair and replacement

Most calls start with a warm house and a thermostat that says the system is running. The usual causes are a failed capacitor, a burned contactor, a clogged drain that tripped the float switch, a frozen coil from low airflow, a refrigerant leak or a compressor that is worn out. We find the cause first, then tell you what it will take.

Fix it or replace it

Age, refrigerant type, coil condition and repair history drive the decision. A newer system with a failed part is usually worth fixing. An older R-22 system with a leaking coil usually is not. We lay out both options and you choose.

Sizing the new system

When a system is replaced, we run a load calculation for the house instead of copying the old tonnage. Oversized systems are common in Collier. They chill the air fast, shut off before pulling moisture out, and leave rooms cold and damp. A right-sized system runs longer, steadier cycles and controls humidity much better.

  • Central split air conditioners and matching air handlers
  • Heat pumps, the standard heating and cooling setup in Southwest Florida
  • Two-stage and variable-speed systems for tighter humidity control
  • Ductless mini-splits for additions, lanais, garages and rooms the ducts never reached
  • Packaged units on homes built for them
  • Programmable and smart thermostats, zoning and humidity controls

New residential equipment now uses lower global-warming refrigerants such as R-454B and R-32 under federal rules that took effect in 2025. Efficiency is rated in SEER2, and the Southeast has a higher minimum for new split air conditioners than northern states. We explain what the ratings mean for your bill rather than pushing the highest number.

Seasonal homes, humidity and drain lines

A big share of Collier homes and condos sit empty for part of the year. When owners head north in spring, the house still needs moisture control. Turning the AC off in a closed Naples or Marco home during summer can lead to mold on walls, closets and furniture within weeks.

  • Leave the system running, set around 78 to 80 degrees, or use a humidity setting if your thermostat has one.
  • Have the condensate line cleared and a float switch checked before you leave.
  • A Wi-Fi thermostat with alerts lets you see if the house warms up while you are away.
  • A whole-home dehumidifier is worth considering if the house stays damp even with the AC running.

Condensate drains are one of the most common calls in the county year-round. Algae grows in the line, the water backs up, and either the float switch shuts the system off or the pan overflows into the ceiling, closet or condo below. We clear lines, add cleanouts, install float switches and secondary pans, and set up drain treatment as part of maintenance.

Ducts, airflow and rooms that never cool

When the equipment checks out and one end of the house is still warm, the ducts are usually the reason. Flex duct sags and kinks, connections pull apart, duct board tape fails, and a single hallway return cannot pull enough air from closed bedrooms. Leaks on the return side pull hot, humid attic air straight into the system.

We inspect, repair, seal and replace ductwork, add returns and transfer grilles, and balance airflow. In larger homes we set up zoning with dampers and separate thermostats, so an upstairs or a guest wing is not cooled all day for nothing. Before quoting a new system, we check the ducts, because new equipment on bad ducts is money poorly spent.

Heat pumps and the few cold mornings

Collier gets a handful of chilly mornings most winters when a front comes through. Most homes heat with a heat pump, which runs the outdoor unit in reverse, backed up by electric heat strips in the air handler. Some older homes still have straight cooling systems with strip heat only, and a few have gas furnaces.

A dusty smell on the first cold morning usually clears fast. A burning smell that lingers, a tripping breaker, or heat that never warms the house needs a look. We service heat pumps, heat strips, reversing valves and defrost controls, and the occasional gas furnace.

Indoor air quality

Homes here stay shut most of the year, so whatever is in the air stays inside. Pollen, mold spores, pet dander and smoke from brush and wildfires in the eastern part of the county all end up at the return.

We start with the basics: the right filter for the equipment, a clean coil and blower, and sealed return ducts. From there we can add media filters, UV lights at the coil, energy recovery ventilators for fresh air, and whole-home dehumidifiers when they fit the house.

Irma, Ian and flooded equipment

Collier took two major storms in five years. Hurricane Irma made landfall on Marco Island in September 2017, with the worst surge along the southern coast at Chokoloskee and Everglades City. Hurricane Ian in September 2022 pushed surge flooding across much of the area south and west of US 41, including neighborhoods along the Gordon River, Rock Creek and the Cocohatchee.

Condensers on ground pads and air handlers in garages were among the first things to go under water. Equipment that sat in salt water usually needs to be replaced, even if it runs for a while after drying out, because corrosion keeps working on controls, motors and coils. Ducts that took on water should be replaced, not dried.

  • Raise condensers on stands or wall brackets when you rebuild.
  • Move air handlers out of the garage or set them up off the floor where possible.
  • Florida code requires outdoor units to be anchored for wind, and we install the tie-downs and stands to match.
  • Know where the outdoor disconnect is, and shut it off if flooding is expected.

In Everglades City and the raised homes near the coast, condensers often sit on platforms. Those platforms and their anchors need to be checked after every major storm.

Immokalee and agricultural buildings

East of the Estates, Collier turns into groves, vegetable farms and cattle land, with Immokalee as the main town. Housing runs from older block homes and mobile homes to rural properties outside the utility district. During harvest season many homes carry more people than they were designed for, and older AC systems struggle with the extra load and the doors opening all day.

Agricultural and commercial properties bring work most residential companies do not touch: cooling for packing and office buildings, walk-in coolers, commercial refrigeration, and equipment rooms that need ventilation. We service and replace that equipment and set up maintenance before the season starts, when a failure costs the most.

Commercial HVAC in Collier

Commercial work in the county runs from medical offices and retail along US 41 and Immokalee Road to restaurants, shopping centers, warehouses and condo buildings. Each one has a different tolerance for downtime.

  • Rooftop units, split systems and packaged equipment: service, repair and replacement
  • VRF and ductless systems for offices and suites that need zoned control
  • Make-up air and kitchen exhaust for restaurants
  • Dedicated cooling for server rooms, electrical rooms and telecom closets
  • Walk-in coolers and commercial refrigeration
  • Chillers, cooling towers and building automation for larger buildings, with specialists brought in when the job calls for it
  • HVAC for tenant buildouts and space changes

Preventive maintenance agreements are the best value on the commercial side. Scheduled visits catch dirty coils, weak capacitors, worn belts and clogged drains before they shut a business down in August. We keep records by unit, so property managers can see what each one needs.

Ave Maria and new construction

Ave Maria and the growing communities in east Collier have kept new construction busy. We handle HVAC on new homes and commercial builds from design through final inspection.

  • Manual J load calculations so equipment fits the house
  • Duct design and sizing so every room gets the air it needs
  • Rough-in, equipment setting, startup and testing
  • Duct leakage testing, which the Florida energy code requires on new construction

In newer homes, the most common calls are first-time maintenance, builder-grade systems that were sized loosely, drain lines that were never set up with a cleanout, and thermostats nobody configured. If you bought new and the house never felt quite right, we can test airflow and tell you why.

Maintenance plans

A yearly service visit before the heat sets in is the best thing you can do for a Collier system. Older equipment and coastal units benefit from two visits a year. Between visits, a few habits help:

  • Check or change the filter every one to three months, more often with pets or construction dust.
  • Pour a cup of white vinegar down the condensate line every month or two in summer.
  • Keep landscaping and fences at least two feet away from the condenser.
  • Rinse salt and grass clippings off the outdoor coil gently with a hose.
  • Before hurricane season, check that the condenser tie-downs are tight.

When to call us

Call when the AC runs but the house stays warm, when there is water around the air handler or a stain on the ceiling, when the outdoor unit hums but does not start, or when you smell burning that does not clear. Call before you buy a home, too, so you know the age and condition of the system before closing.

Our office is in Fort Myers and is open Monday through Friday, 8am to 5pm. When you reach out, it helps to have the address, the model label from the outdoor unit and any condo management contact handy. HomeFlow is insured and works across Collier, Lee and Charlotte Counties. Call (239) 518-4198 or use the service request form.

Common Questions

My address says Naples. Does the City of Naples issue my AC permit?

Only if the property is inside city limits. Many Naples addresses are in unincorporated Collier County, where Collier County Growth Management issues the permit. We confirm from the parcel record before filing.

Do I need a permit to replace my air conditioner in Collier County?

Generally yes. Replacing an air conditioner or heat pump needs a mechanical permit from the county, the City of Naples or the City of Marco Island depending on the address. We pull it as part of the job.

Can you replace a rooftop condenser on a condo building?

Yes. We work with management on access, insurance paperwork and work hours, and we arrange the lift when equipment has to come off the roof.

Should I turn off my AC when I leave for the summer?

No. Set it around 78 to 80 degrees or use a humidity setting. A closed-up Collier home with no cooling can grow mold within weeks.

My AC died after a lightning storm in Golden Gate Estates. What failed?

Often a control board, contactor or capacitor, sometimes the compressor. We test the components and can add a surge protector at the disconnect to help next time.

My equipment sat in surge water during Ian. Can it be saved?

Usually not if it was salt water. Corrosion keeps working on controls, motors and coils after the unit dries out. Wet ducts should be replaced too.

Do you service walk-in coolers and commercial refrigeration?

Yes, along with rooftop units, VRF systems, kitchen make-up air and maintenance agreements for commercial and agricultural buildings.

Need AC service?

Call (239) 518-4198 or send us a request and we will get back to you.

Scroll to Top