Leer esta página en español · Ler esta página em português
When the buried line between your water meter and your house keeps leaking or is made of a material known to fail, replacing the whole run is often smarter than patching it again. HomeFlow Plumbing replaces main water service lines across Southwest Florida, with trenching or boring to protect your driveway and landscaping. Call (239) 518-4198 to talk through your line.
What Water Line Replacement Covers
This page is about replacing the entire main service line, the buried pipe that runs between your water meter and the point where the supply enters your house. It is a different job than fixing one leak in that line. If you have a single break and the rest of the pipe is sound, our water line repair page covers that work.
Replacement means we abandon or remove the old pipe and install one continuous new run, usually with no buried joints in the yard. The job ends at the house shutoff valve. Piping inside the walls and slab is a separate project, covered on our whole house repiping page.
Homeowners usually reach this point for one of three reasons: the line has leaked more than once, the pipe material is known to fail, or a larger project (a city hookup, a driveway replacement, a pool) is already opening up the yard and it makes sense to replace the line while the ground is open.
Who Owns Which Side of the Meter in Southwest Florida
The meter is the dividing line almost everywhere in our area. The utility owns and maintains the meter and the pipe coming to it from the main. The property owner owns everything downstream. That means the service line to the house is your pipe, your leak and your repair, even when part of it sits under a public sidewalk on its way to the house.
The Florida Public Service Commission’s consumer guidance says the customer, not the utility, is responsible for charges related to leaks on the customer’s side of the meter. Each utility words its own rules a little differently:
| Utility | What the utility handles | What the owner handles |
|---|---|---|
| City of Cape Coral | Meters and the service pipe from the main to the point of delivery (where city pipes or meters connect to the customer’s pipe). City code says the city is not responsible for maintaining the customer’s pipes. | Pipes, shutoffs and valves on the customer’s side of the point of delivery, installed and maintained to city codes. |
| Lee County Utilities | Meter and utility-side service. | Customer-side piping, plus maintaining, repairing and replacing any required backflow device. |
| Charlotte County Utilities | County field staff repair or replace meter boxes, lids and meters. | The owner of record is responsible for the account and for problems on the house side. |
| Collier County Water-Sewer District | Service lines that carry water from the public main to the meter. | Customer-side lines. If you damage a county backflow device, the county bills for the device and installation time. |
| City of Fort Myers and City of Naples | Meter and utility-side service. | House-side piping. Confirm the exact handoff point with the utility before digging. |
If the leak is in the meter box itself, on the meter couplings or on the street side of the meter, call the utility first. We do not touch the meter, and in Cape Coral the city specifically instructs that the dual check valve it installs on the meter must not be removed.
The curb stop and the house valve
The utility-side valve in or beside the meter box is often called the curb stop. It is utility equipment, and some utilities lock or tag it, so ask before operating it. Before a replacement starts, both the curb stop and your house shutoff have to close fully, because the old line is cut on both ends. A curb stop that will not seal goes back to the utility before we can proceed. If your house valve is also suspect, it gets replaced as part of the job.
Old Service Line Materials in SW Florida Homes
The age of the house is the best first clue to what is in the yard. Southwest Florida has a lot of housing built in the 1970s through the 1990s, and the service lines from that era are the ones reaching the end of their life.
Polybutylene
Polybutylene was used in both interior plumbing and yard service lines. The 1995 Cox v. Shell class action settlement covered owners of polybutylene plumbing systems and yard service lines nationwide, and its claim deadline has long since passed. Water with significant chlorine levels was cited as a factor in failures. In the yard it is usually a gray or blue flexible plastic line. Failures tend to start at fittings and at points where the pipe was bent or stressed, and once one section fails, others usually follow. If your house also has polybutylene inside, see our polybutylene replacement page.
Galvanized steel
Older homes and some early commercial buildings may still have galvanized steel service pipe. It corrodes from the inside, which narrows the bore and drops pressure, and from the outside in wet, sandy soil. Collier County’s water utility recommends that residents remove any remaining lead or galvanized water lines. Galvanized lines rarely justify a spot repair because the pipe next to the leak is usually in similar shape.
PVC
Schedule 40 PVC is common on homes built or connected since the 1980s, and Cape Coral’s published hookup instructions call for Schedule 40 or 80 PVC between the meter and the building. PVC itself holds up well underground. The weak points are glued joints, fittings stressed by settling or roots, shallow sections that get crushed by vehicles, and lines nicked by irrigation or fence work.
Copper
Copper service lines are less common here but show up in some older and higher-end homes. Copper can pit in aggressive soil or where it contacts other metals, and it can wear through where it rubs on rock or concrete. A green or blue stain on fixtures, pinhole leaks and wet spots along the line route are typical signs.
Replace or Repair Again: Decision Rules
The symptoms of a failing service line (wet yard, a moving meter dial, a pressure drop) are covered on our water line repair page. Once you know the leak is in the service line, these are the rules we use to decide whether to patch it or replace the whole run:
- Material rule. Polybutylene and galvanized steel get replaced, not patched. The pipe on either side of the leak is the same age and the same material, and the next failure is usually close behind.
- Repeat rule. A second leak in a different spot on the same line tips the decision toward replacement, even on PVC. Two unrelated failures say the line has a problem along its length: shallow burial, poor bedding, or stressed joints.
- Access rule. If the old route now runs under a pool deck, an addition, a paver driveway or a slab that was built after the house, every future repair means demolition. Rerouting a new line around those structures can cost less over time than one more repair under them.
- Timing rule. If the yard is being opened anyway for a sewer connection, a driveway, a pool or new landscaping, replacing the line in the same trench window avoids digging twice.
- Size rule. If the existing line is 3/4 inch and the house has grown (more bathrooms, a larger irrigation system, a tankless heater), a replacement is the chance to step up to 1 inch.
If the location of the leak is still unknown, leak detection comes first. If the line has already split and water is flowing, start with burst pipe repair and plan the replacement afterward. For pressure complaints that may come from the house piping instead, see water pressure problems.
Choosing the New Pipe: PEX, HDPE, Copper or PVC
Plumbing code requires water service pipe to be rated for at least 160 psi at 73°F and to be at least 3/4 inch. Within those rules there are several good choices. The right one depends on the length of the run, whether we are boring or trenching, what the utility and building department will accept, and how the line connects at each end.
| Material | Strengths | Watch-outs |
|---|---|---|
| PEX water service tubing | Flexible, comes in long coils so most runs have no buried joints, handles soil movement well, suited to directional boring. | Must be kept out of sunlight before burial. Buried fittings must be listed for buried service; compression fittings with stainless steel inserts are a common choice. |
| HDPE (polyethylene) service tubing | Made for buried water service under AWWA C901, commonly sold in copper tube size and DR9 or SDR9 coils, very tough, a standard choice for boring. | Needs compression or fused fittings rated for it. Transition fittings are needed where it meets PVC or the house riser. |
| Type K copper | Thickest wall of the common copper types, long track record underground, rigid and strong. | Can pit in aggressive soil, needs bedding that keeps it off rock, more joints on long runs. |
| Schedule 40 or 80 PVC | Specified in Cape Coral’s hookup instructions, easy to inspect, works well in open trench. | Glued joints every 20 feet, brittle if crushed or struck, not suited to boring under driveways. |
Our usual approach is one continuous run of PEX or HDPE wherever the local utility and building department accept it, because the fewer joints in the ground, the fewer places for a future leak. Where a jurisdiction’s standards call for PVC, we use PVC and pay extra attention to bedding and depth. Copper is a good fit when the owner wants it or when local conditions favor metal pipe.
Trenching vs Directional Boring
Service lines often pass under a driveway, a walkway or a landscaped bed on the way to the house. How we get the new pipe in the ground decides how much of your yard gets disturbed.
Open trench
A narrow trench along the route is the simplest method. It works well when the line runs under grass or mulch beds with nothing permanent on top. It lets the inspector see the whole pipe, the bedding and the depth. It is the most practical method when the old line has to come out completely, or when other lines (sewer, irrigation) share the corridor and have to be checked.
Directional boring
A small horizontal drill tunnels under the driveway, pavers or a mature hedge and pulls the new pipe back through, leaving the surface in place. Only small pits at each end are dug. Flexible pipe like PEX or HDPE is the natural choice for a bore. The plastics industry’s PEX installation guidance calls out protecting the tubing from gouging on sharp rock during a pull, which matters here where the soil can carry shell and limestone.
A combination
Many jobs use both: an open trench through the lawn and a short bore under the driveway. We decide route by route. The goal is to avoid cutting concrete or lifting pavers you care about while still giving the inspector what they need to see.
Every method starts with a utility locate. After the 811 marks are in, we still probe and hand-dig near the meter and the house, since private sprinkler pipe, landscape lighting and old abandoned lines are not marked.
Code and Inspection Points for a New Service Line
Florida’s plumbing code is based on the International Plumbing Code, with local utility standards layered on top. These are the points that most often decide whether a service line passes inspection:
- Size. At least 3/4 inch. Larger homes, long runs and homes with irrigation on the same service often need 1 inch to hold pressure.
- Depth. Cape Coral’s hookup instructions require the pipe to be at least 12 inches deep after final grade. Industry guidance for PEX under surface traffic calls for at least 24 inches of cover. We set depth to the stricter of the local standard and the location.
- Separation from the sewer. Code calls for 5 feet of undisturbed or compacted earth between the water service and the building sewer when they are in separate trenches, with narrow exceptions for a water line on a solid shelf at least 12 inches above the sewer or a sleeved crossing.
- Bedding and backfill. The pipe sits on clean sand or fine soil with no rock or shell against it, then gets backfilled and compacted in layers.
- Shutoff at the house. A full-open valve where the line enters the building.
- Pressure test and disinfection. The new line is tested and chlorinated. Cape Coral requires notarized affidavits for the water test and chlorination before it schedules the inspection.
- Open trench at inspection. Inspectors expect to see the pipe, the depth and the connections before backfill, so the trench stays open until the inspection passes.
- No bypass. All water must pass through the meter. Cape Coral’s code prohibits bypass connections around it.
Permits by Jurisdiction
Replacing a service line is plumbing work in the ground, and the local building department expects a permit. Which office issues it depends on where the property sits, not on which utility supplies the water.
| Location | Permitting office | Notes |
|---|---|---|
| Unincorporated Lee County (Lehigh Acres, Alva, San Carlos Park, Gateway, Fort Myers Shores and more) | Lee County Building, applied for through its online portal | A plumbing permit is required for installation, replacement or relocation. Connecting lawn irrigation to a potable water source needs a separate irrigation permit. |
| City of Cape Coral | City permitting division | Utility hookup work also involves Customer Billing Services, affidavits and city inspection of the water, sewer and irrigation services. |
| City of Fort Myers, Bonita Springs, Estero, Sanibel, Fort Myers Beach | Each city or village building department | Each has its own permit portal and inspection scheduling. |
| Charlotte County and Punta Gorda | Charlotte County Community Development or City of Punta Gorda | Utility questions go to Charlotte County Utilities. |
| Collier County, City of Naples, Marco Island | Collier County Growth Management, City of Naples or City of Marco Island | Collier’s water utility handles meters and backflow devices. |
We file the permit before work starts and schedule the inspections. Owners can pull their own permits as owner-builders in some places, but that makes the owner responsible for the work meeting code.
Irrigation Tie-Ins and Backflow
A lot of SW Florida homes have the sprinkler system tied into the potable service line somewhere between the meter and the house. A replacement exposes that connection, and it has to be brought up to current rules when the new line goes in.
- Cape Coral’s hookup instructions require a vacuum breaker on the sprinkler system when the potable water feeds it, and they prohibit any cross connection between potable water and a non-potable source.
- Cape Coral irrigation water from the city’s reclaimed system cannot be used for drinking, bathing or filling a pool, and it cannot be piped into the house. Any old link between the house line and the irrigation supply has to be removed.
- In unincorporated Lee County, an irrigation connection to potable water has its own permit, and the inspection may include a check valve certification.
- Lee County Utilities makes the owner responsible for maintaining, repairing and replacing a required backflow device. Collier County requires its reduced pressure backflow assemblies to sit at least 12 inches above finished grade.
- Commercial, industrial and buildings with three or more units in Cape Coral need a reduced pressure assembly right after the meter, tested every year by a certified tester.
If your property has a testable backflow assembly, we can coordinate the annual test through our backflow testing service.
Coordinating With UEP Hookups and Well-to-City Conversions
When the Utilities Extension Project brings city water to a Cape Coral neighborhood, the city sets the connection deadline from the Notice of Availability. The hookup itself, including fees, applications and septic abandonment, is covered on our Cape Coral UEP sewer and water hookup page. What matters here is how the service line fits into that project.
The new potable line runs between the city meter and the house, and in many cases it replaces piping that used to come from a private well. If you are planning a sewer lateral, a well disconnect and a water line all in the same season, doing them under one coordinated plan means the yard is opened once. It also lets us keep the water and sewer lines properly separated, since both run from the house toward the street.
Cape Coral’s instructions also note that the city’s irrigation fitting at the service box must be fed with 1 inch Schedule 40 PVC buried at least 12 inches, and that the irrigation system must be disconnected from well piping before it connects to the city’s irrigation water.
Well-to-city conversions outside UEP areas
Outside the UEP areas, well-to-city conversions happen in Lehigh Acres, parts of North Fort Myers, Golden Gate Estates and other areas when a water main reaches the street. Cape Coral’s code requires that once municipal potable water is available within 200 feet, connections be made so the well is no longer used for human consumption.
The conversion usually means a new service line from the new meter to the house, a disconnect between the well and the house plumbing, and a decision about what to do with the well. Common choices are keeping the well for irrigation only (where local rules allow it), or abandoning it. Either way, the well and city water can never be connected. The pressure tank, filtration and softener loop often sit on the old well line, so the new service has to be tied in at the right point, usually before any equipment you want to keep.
For well equipment you are keeping for irrigation, see our well pump page. Lehigh Acres owners can also read our Lehigh Acres wells, septic and sewer guide.
How a Water Line Replacement Job Runs
Every property is different, but the order of work stays about the same:
- Assessment. We find the meter, the house entry and the current route, dig a small test hole to confirm the old material, check pressure at the house and note every sprinkler, lighting or drain line crossing the path.
- Plan the route and method. Straight shot, trench, bore or a combination, based on driveways, trees, pools and other lines.
- Permit and locates. The permit is filed, 811 marks are requested, and we wait for both before digging.
- Shut down and isolate. Water is off at the meter side and the house side. Expect to be without water for part of a day.
- Irrigation and well separation. Any sprinkler tie-in is rebuilt with the required backflow protection, and any old well connection is cut and capped.
- Install the new line. The new pipe goes in at the planned depth with proper bedding. Transition fittings at the meter outlet and the house riser are matched to both materials, since a poor transition is a common leak point.
- Test, flush and disinfect. Pressure testing, flushing debris and chlorination as the local office requires. In Cape Coral the test and chlorination are certified by notarized affidavit.
- Inspection. The trench stays open until the inspector passes it.
- Backfill and restore. Compacted backfill, then the surface is put back.
- Abandon the old line. The old pipe is cut and capped at both ends or removed if it is in the way.
After water is restored, faucet aerators and the water heater may pick up loose sediment for a few days. Running cold water through each fixture after the job helps clear it.
Restoring Pavers, Sod and Landscaping
Restoration is part of the plan, not an afterthought. Before the first shovel goes in, we walk the route with you and agree on what gets lifted and how it goes back.
- Pavers. Lifted pavers are stacked, then reset on compacted base and sand. Pavers rarely come back perfectly level if the base is not compacted in layers, so that step gets extra time.
- Sod. Cut sod can be rolled back if the trench is narrow and the job is short. Wider trenches or long jobs usually need new sod, and new sod needs regular watering for its first few weeks.
- Concrete driveways. Boring under is usually preferred. If a cut is unavoidable, it is a saw cut and patch, and the color will not match exactly.
- Plants and trees. We route around root zones where we can. Shrubs in the path can be dug and set aside.
- Irrigation. Sprinkler lines and wires crossing the trench are repaired and the zone is tested before we leave.
How to Prepare and What Affects Scope
A few things you can do before the job:
- Find the meter box and make sure it is not buried under mulch or blocked by a parked vehicle.
- Move cars, boats, trailers and planters off the route.
- Tell us about sprinkler lines, landscape lighting, invisible pet fences or septic and drainfield areas you know of.
- Gather any old permits, surveys or hookup paperwork, which help show where the line runs.
- Plan for the water to be off for part of the day and store a few gallons for drinking.
- If you rent the home or it is in an HOA, give notice and get any required approval for work in common areas.
- Keep pets indoors while the trench is open.
We do not quote prices on this page, but these are the factors that change the size of the job:
- Length of the run and the number of turns.
- What sits on top of the route: grass, pavers, concrete, a pool deck.
- Whether part of the route needs boring.
- Pipe size and material.
- Whether irrigation, backflow or a well disconnect is part of the job.
- Local permit and inspection requirements.
- Restoration work.
To schedule an assessment, call (239) 518-4198 during office hours, Monday to Friday, 8am to 5pm, or reach us through our contact page.
Common Questions
Does the utility pay for any part of a water line replacement?
No, not for the pipe on the house side of the meter. That section belongs to the property owner in every utility we serve. The utility handles the meter and the street side, and the Florida Public Service Commission’s consumer guidance also says customers are responsible for leak charges on their side of the meter.
How do I know if I need a repair or a full water line replacement?
A single leak on PVC that is otherwise in good shape is usually a repair. Repeated leaks, polybutylene or galvanized pipe, low pressure that traces to the service line, or a yard that is already being dug up all point to replacement.
Can the new line take a different route than the old one?
Yes, and it often should. If the old route runs under a pool deck, an addition or a paver driveway, we can lay the new line along a path that stays reachable, as long as it keeps proper separation from the sewer line and meets local depth rules.
What pipe do you use for a new service line?
Most often one continuous run of PEX or HDPE water service tubing, because it means no buried joints in the yard. Where local standards call for PVC we use PVC, and Type K copper is an option too. All of them must be rated for at least 160 psi and be at least 3/4 inch.
Does the old pipe have to be dug up?
Usually not. The old line is cut and capped at both ends and left in the ground, unless it sits in the new route or the inspector asks for it to come out. A permit and inspection are still required for the new line.
How long will I be without water?
Most homes are without water for part of a day while the old line is disconnected and the new one is tied in, tested and disinfected. The inspection timing can extend how long the trench stays open, but water is normally restored before the inspection.
What happens to my sprinkler connection?
It gets checked and brought up to current rules. In Cape Coral, a sprinkler system fed by potable water needs a vacuum breaker, and in unincorporated Lee County an irrigation connection to potable water needs its own permit.
I am switching from a well to city water. Do I need a new service line?
Yes, the new meter needs a new line to the house, and the well must be fully separated from city water. You may be able to keep the well for irrigation depending on local rules, and the softener or filter loop may need to be re-tied.
Why HomeFlow
- One company for service calls, remodels and new construction, so you’re not lining up a different plumber for each job.
- We work in Lee, Charlotte and Collier Counties and know the pipe, water and slab issues that come with homes here.
- Call (239) 518-4198 or send a request online. Tell us what’s going on and where, and we’ll take it from there.
Related Pages
Related services
Areas
Plumbing guides
Need a plumber?
Call (239) 518-4198 or send us a request and we’ll get back to you.
