Leer esta página en español · Ler esta página em português
HomeFlow now handles heating and air conditioning in Everglades City, Chokoloskee and Plantation Island, with planned trips down State Road 29 for stilt homes, older ground-level houses, mobile homes and local businesses.
HVAC Services in Everglades City and Chokoloskee
Planned Trips
How we schedule the drive and group calls so the visit covers everything.
Stilt and Ground-Level Homes
AC repair, heat pumps, ductwork and replacements, with equipment set above flood level.
Storm Recovery
Checking and replacing flooded condensers, air handlers and ducts after surge.
Commercial
Restaurants, seafood coolers, lodges and offices along the river and the causeway.
Air conditioning at the end of the road
Everglades City sits on the Barron River just inland from Chokoloskee Bay, and Chokoloskee is its own island community to the south, tied to the mainland by a causeway finished in 1956. Everglades National Park wraps around both, Big Cypress National Preserve lies to the north and east, and the nearest big-box store is a long way off. When the air conditioning quits here, you cannot just run to the supply house for a part.
HomeFlow is a Fort Myers plumbing company that now handles heating and air conditioning, and we already make planned trips to this corner of Collier County. We repair and replace central air conditioners and heat pumps, service air handlers, install ductless mini-splits and packaged units, repair ductwork, clear condensate drains, set up thermostats and dehumidifiers, and look after coolers and rooftop equipment for local businesses.
Call (239) 518-4198 or use our service request form to get on the schedule. Tell us whether your house is raised or at ground level, and send photos if you can. That one step does more than anything else to make the trip work.
How we schedule the drive
We will be straight about distance. From our office in Fort Myers, Everglades City is down I-75 and south on State Road 29 through Copeland, or around on US 41 through Carnestown. It is not a quick trip, and we do not promise arrival times for this area. What we do is plan the day so the drive pays off.
- Photograph the data plates on the outdoor unit and the air handler. They show the model, the size and the refrigerant, so we bring the right capacitor, motor or contactor the first time.
- Tell us everything the system has been doing, not just today’s problem. A noisy fan and a dripping drain can be handled on the same visit as the repair.
- Email photos to help@homeflowfl.com along with your address and a phone number.
- Seasonal owners can line up work for the weeks they are in town, or arrange access with a neighbor or manager.
- If a system is iced over or leaking water, switch it off at the thermostat and call us at (239) 518-4198.
We try to group calls in Everglades City, Chokoloskee and Plantation Island on the same day. When the State Road 29 corridor takes us through Immokalee, we sometimes pair trips with work there too.
Two feet above sea level, or twenty
Height decides a lot about HVAC here. Everglades City sits roughly two feet above sea level. Chokoloskee is different: parts of the island rise to around 20 feet because they are built on shell mounds that Native Americans piled up over more than 2,000 years. A condenser on a pad on high ground on the island may have stayed dry through storms that swamped the same unit in town.
That is why we never assume where equipment should go. We look at the lot, the flood zone, the elevation certificate if you have one, and the water marks from past storms. A unit on a ground pad might be fine on a shell mound lot and a bad bet on a low street near the river.
Stilt homes and equipment up in the air
After Irma, homes in this area that were rebuilt or substantially damaged had to go up, first to the 100-year flood level and then higher after Collier County raised its minimum in 2019. Many owners lifted houses on concrete pilings ten feet or more. Florida flood rules generally require equipment serving an elevated building to sit at or above the required flood elevation, and that includes the air conditioner.
What a good setup looks like
- The condenser on a platform or wall bracket attached to the structure, anchored for wind
- The air handler inside the living space, not in a ground-level storage room
- Refrigerant lines run up the structure, strapped tight, insulated and shielded from sun and debris
- A condensate drain that slopes properly from the raised air handler to a safe discharge point
- Ducts inside the conditioned envelope, not hung in the open under the floor
What we find instead
Some raised homes still have the condenser sitting on a slab under the house, because that was easier at the time or because it was moved back down after a repair. Others have line sets flapping against pilings or insulation baked off by the sun. Ducts run through an open floor system lose heat to the outside air and sweat in the humidity. When we are already working on a raised house, we point these out and fix what makes sense.
Getting a platform condenser serviced or replaced takes planning. Tell us how high it sits and how we reach it, because a tall platform may need extra equipment on the truck.
Older ground-level houses that have flooded more than once
Not everybody raised their house. Lifting a home is expensive, and second homes do not qualify for federal elevation assistance, so plenty of older ground-level houses remain. Many have taken water several times: Donna in 1960, Wilma in 2005, Irma in 2017, and Ian again in 2022.
The HVAC in these homes is often a patchwork. A condenser replaced after one storm, an air handler swapped after the next, ducts patched where they got wet. Mismatched indoor and outdoor units are common, and a mismatch can cut efficiency and cause freezing coils or poor humidity control. Old systems may still run on R-22, which has not been produced in the US since 2020.
Choices for a house that may flood again
- Raise the condenser on a stand or bracket even if the house stays at grade
- Move the air handler to the highest practical spot, such as a raised closet platform or the attic
- Use ductless mini-splits with wall-mounted heads that sit well above the floor
- Keep ducts out of spaces likely to flood
- Size the replacement with a load calculation instead of copying the last unit
Each of those steps limits what the next surge can reach. We will talk through what fits your house and your budget.
Mobile homes, RV lots and fishing camps
The area has a good number of mobile homes, RV parks and fishing camps, many used only part of the year. Cooling in these places works differently from a site-built house.
- Manufactured homes usually have ducts in the floor, with a crossover duct between sections that can tear or come loose
- Many use packaged units on a pad beside the home, or a split system with a down-flow air handler in a closet
- Skirting and underfloor spaces trap moisture, so duct leaks under the home pull in damp air
- Fishing camps and small cabins often run through-wall units or window units that wear out quickly in salt air
- Small offices and bunk rooms are good candidates for ductless mini-splits
We check the crossover duct, the belly ducts we can reach, the condensate drain and the electrical connections, and we talk about whether a ductless system would serve a small space better than an aging packaged unit.
Ducts, airflow and thermostats
When one room stays warm or the system runs all afternoon without catching up, the ducts are often the reason. In older homes they sit in hot attics with joints that have pulled apart. In homes that flooded, sections may have been patched rather than replaced. In raised homes, ducts that were hung under the floor lose cooling to the outside air and drip condensation onto whatever is stored below.
- Inspecting and sealing duct joints, boots and the air handler connection
- Replacing crushed, torn or storm-damaged duct runs
- Adding a return where the house only has one small grille
- Balancing airflow so far rooms get their share
- Moving a thermostat off a sunny wall or away from a door
- Smart thermostats with humidity control and remote alerts
For a raised house with two living floors, a second system or a ductless head upstairs is sometimes a better answer than trying to push more air through one duct system. We will measure before we recommend either.
Salt, sun and mangroves
You are surrounded by salt water out here, and the air carries it into every condenser coil. Fins corrode and crumble, cabinet bottoms rust through, electrical terminals green over and fan motor bearings fail. Add strong sun on rooftop and platform units, and outdoor equipment here ages faster than the same model in inland Naples.
At replacement time we look at coastal coil protection, stainless or coated hardware and UV-resistant line set covers. Between visits, a gentle freshwater rinse of the outdoor coil helps. Never use a pressure washer on the fins. On maintenance trips we clean coils properly and tighten and treat electrical connections, because loose, corroded terminals cause a lot of the no-cooling calls in coastal towns.
Humidity, empty houses and the air indoors
Everglades City and Chokoloskee sit in the middle of one of the wettest landscapes in the country, and summer humidity is relentless. A lot of homes sit empty for weeks or months at a time. Shut the AC off in an empty house here and mold will be waiting when you get back.
Before you leave for a while
- Leave the system on, set somewhere around 78 to 82 degrees, or use a humidity setting
- Put in a new filter and have the drain line flushed and the float switch tested
- Consider a whole-home dehumidifier if the house stays damp even with the AC running
- Ask about a thermostat or sensor that alerts you if temperature or humidity climbs
- Have a neighbor look in after storms and power outages
Air quality
Smoke from fires in the Glades, pollen and mold spores all end up in the return. A better filter, a sealed return, a clean coil and a UV light at the coil help most homes. For tight new stilt homes, an energy recovery ventilator can bring in fresh air without adding much moisture.
Power outages and your air conditioner
Irma knocked out power here for days, and summer storms still cause outages and voltage dips. Air conditioners do not like either. A compressor that tries to restart against high pressure after a blip, or runs on low voltage, can trip breakers and wear out capacitors.
Surge protection at the outdoor unit and a time-delay restart on the thermostat or control board help. If you have a generator, it needs to be sized for the starting load of the AC, and a hard-start kit or a soft starter can make a big difference. We can check what your system draws and tell you what a generator would need to run it.
After Irma, Ian and the next one
Irma’s surge in September 2017 put water waist-high in a local supermarket and a foot or two inside many homes. Ian passed offshore in September 2022 and still pushed more than three feet into that same store. Ground-level condensers, garage air handlers and ducts in flooded spaces were ruined both times. Even raised homes lost equipment that had been left on the ground below.
After a flood
- Keep power off to any condenser or air handler that took water until it has been checked
- Expect salt-flooded equipment to need replacement, even if it seems to run
- Replace wet ductwork and duct insulation rather than drying it
- Look for condensers that shifted on their pads or lost their tie-downs
- Photograph damage and keep receipts for insurance
Florida code requires outdoor units to be anchored for wind. When we replace storm-damaged equipment, we install the tie-downs and stands to match, and we raise the equipment wherever we can.
Repairs, replacements and refrigerants
The usual no-cooling causes are the same here as anywhere: a weak capacitor, a burned contactor, a refrigerant leak, a frozen coil or a clogged drain that tripped the float switch. Distance just makes it more important to diagnose correctly and carry the parts.
When the repair is large, we compare it honestly with replacement. New residential systems now use lower-GWP refrigerants such as R-454B and R-32 under federal rules effective in 2025, and efficiency is rated in SEER2, with a higher minimum for new split systems in the Southeast. A properly sized heat pump with sealed ducts usually beats a bigger unit on comfort and humidity.
Heat pumps and cold fronts
A few cold fronts reach this far south most winters, and winter is when many seasonal owners are here. Most homes heat with a heat pump backed by electric heat strips. Some older homes and mobile homes have a straight AC with heat strips only.
A brief dusty smell the first time the heat runs is normal. A lingering burning smell, a tripping breaker or cold air in heat mode needs a look. We service reversing valves, defrost controls, heat strips and sequencers.
Commercial HVAC for local businesses
Business here runs on fishing, seafood, tourism and the visitors heading into the park. That means restaurants, seafood houses, small lodges and motels, tour and guide offices, stores and city buildings, most of them close to the water and busiest in the cooler months.
Commercial work we handle
- Walk-in coolers, reach-in refrigeration and ice machines for restaurants and seafood businesses
- Rooftop and packaged units, with coastal coil options at replacement
- Split and ductless systems for offices, shops and guest rooms
- Through-wall and PTAC units in lodges and motels
- Kitchen exhaust and make-up air
- Cooling for electrical, network and phone rooms
- HVAC for tenant buildouts and remodels
Large central plants with chillers, cooling towers and building automation are rare in a town this size. Where a building has them, we coordinate with the right specialists.
Maintenance agreements
A seafood cooler that fails during the season can cost a lot of product in a few hours. We set up preventive maintenance with coil cleaning, door gasket and drain checks, refrigerant checks and written notes, scheduled on our trips so the work happens before the busy months.
New stilt homes and rebuilds
For new construction and rebuilds, we handle HVAC from the load calculation to the final inspection. A Manual J calculation accounts for the house’s windows, orientation, insulation and exposure, which matters on a raised house that catches sun and wind on every side.
- Load calculations, equipment selection and duct design
- Platform locations and air handler placement above flood elevation
- Rough-in coordinated with the builder
- Duct leakage testing, which the Florida energy code requires on new construction
- Startup, airflow testing and wind anchoring
Permits: city, county and the 50 percent rule
The City of Everglades contracts with Collier County for building inspections under an interlocal agreement signed in 2018, so county inspectors handle mechanical inspections inside the city. The city keeps its own floodplain ordinance and land development code, and its office takes permit questions. Chokoloskee and Plantation Island are unincorporated, so Collier County handles them directly. An AC or heat pump changeout generally needs a mechanical permit either way, and we pull it.
Flood rules matter too. If repairs or improvements to a building in a flood zone reach 50 percent of its market value, the whole building has to be brought into compliance, usually by elevating it. HVAC costs count toward that total, so get the full picture before committing to a big rebuild.
Maintenance and when to call
An annual maintenance visit on one of our planned trips is the best way to avoid an emergency at the end of a long drive. We clean the condenser coil, check electrical parts and refrigerant, flush the drain, test the float switch, change the filter and inspect stands and tie-downs.
Call when the house is warm and the AC is running, when water shows up around the air handler, when the outdoor unit hums but does not start, or before you buy a home and want to know the age of the system. Reach us at (239) 518-4198 or through the service request form. Office hours are Monday through Friday, 8am to 5pm. Our Marco Island page covers the island to the northwest, where the salt and flood problems look a lot like yours.
Common Questions
Do you really come out to Everglades City and Chokoloskee?
Yes, on planned trips. We group calls in Everglades City, Chokoloskee and Plantation Island on the same day. Photos of your equipment data plates help us bring the right parts the first time.
Who issues the permit for an AC replacement inside Everglades City?
The city contracts with Collier County for building inspections, so county inspectors handle the mechanical inspection, while the city keeps its own floodplain rules. Chokoloskee and Plantation Island go straight through Collier County.
My condenser sits on the ground under my stilt house. Should it be moved?
Usually, yes. Equipment serving an elevated building should sit at or above the required flood elevation. A platform or bracket on the structure keeps it out of the next surge.
Can flooded AC equipment be saved?
Rarely. Salt water corrodes coils, motors and controls from the inside, and the unit often fails weeks later. Wet ductwork should be replaced. Keep power off until the system has been checked.
Can my generator run my air conditioner?
It depends on the generator’s size and the AC’s starting load. A hard-start kit or soft starter can reduce that load. We can measure what your system draws and tell you what it would take.
What should I do with my AC when I leave for the season?
Leave it running around 78 to 82 degrees or on a humidity setting, with a fresh filter and a clean drain line. A closed house here grows mold quickly without cooling.
Do you service walk-in coolers and restaurant equipment?
Yes. We work on walk-in coolers, ice machines, rooftop and split systems, kitchen exhaust and make-up air, and we offer maintenance agreements scheduled around our trips.
Related Pages
Nearby areas
- East Naples & Lely
- Golden Gate Estates
- Isles of Capri
- Orangetree
- Collier County
- Naples
- Golden Gate
- Immokalee
- Ave Maria
Plumbing
Need AC service in Everglades City or Chokoloskee?
Call (239) 518-4198 or send us a request and we will get back to you.
