Plumber in Punta Gorda Isles and Burnt Store

Leer esta página en español · Ler esta página em português

Punta Gorda Isles and the Burnt Store corridor sit only a few miles apart, but they run on different water systems, fall under different building departments, and were built in different decades. HomeFlow Plumbing works on homes, condos and commercial spaces along this stretch of Charlotte Harbor, and we sort out which rules apply to your address before we start. Call (239) 518-4198 to tell us what’s going on.

Plumbing Services in Punta Gorda Isles and Burnt Store

Residential

Leaks, drains, water heaters and repipes for Punta Gorda Isles and Burnt Store homes.

Commercial

Service and repairs for offices, retail and other commercial buildings in Punta Gorda Isles and Burnt Store.

Remodels

Bathroom and kitchen remodels, and repiping while the walls are open.

New Construction

Plumbing for new homes and commercial builds in and around Punta Gorda Isles and Burnt Store.

Four Neighborhoods, Three Building Offices

People say “Burnt Store” like it’s one place. For plumbing purposes it isn’t. Here’s how the area breaks down, heading south from downtown Punta Gorda toward Cape Coral.

  • Punta Gorda Isles (PGI): the canal neighborhood west of US 41 inside the City of Punta Gorda. It was dredged and platted starting in the late 1950s, and most of the original houses went up through the 1960s and 1970s.
  • Burnt Store Isles (BSI): also inside city limits, just south of PGI, with sailboat-access canals to the harbor. It built out later than PGI, and a large share of its houses are from the 1980s onward.
  • Burnt Store Lakes and the Burnt Store Road corridor: unincorporated Charlotte County, with Punta Gorda 33955 mailing addresses. Mostly newer construction mixed with vacant lots that are still filling in.
  • Burnt Store Marina: a census-designated place that sits just across the line in Lee County, between Charlotte County to the north and Cape Coral to the south.

That last point catches people. A home at Burnt Store Marina can have a Punta Gorda mailing address and still be in Lee County. So a water heater replacement or repipe in PGI or BSI gets permitted through the City of Punta Gorda, the same job in Burnt Store Lakes goes through Charlotte County, and at the marina it goes through Lee County. Three offices, three sets of inspectors, all within about a 15-minute drive. We confirm jurisdiction from the parcel record before we pull anything.

Who Supplies Your Water and Takes Your Sewage

The provider matters more than most people think. It decides who you call about a main break, what’s in your water, and how hard that water is on fixtures and heaters.

AreaUsual water sourceSewerBuilding permits
Punta Gorda IslesCity of Punta Gorda utility (surface water from Shell Creek)City sewerCity of Punta Gorda
Burnt Store IslesCity of Punta Gorda utilityCity sewerCity of Punta Gorda
Burnt Store Lakes / Burnt Store RoadCharlotte County Utilities, Burnt Store system, or a private well on some lotsCounty sewer where lines exist, septic on othersCharlotte County
Burnt Store MarinaCharlotte County Utilities, Burnt Store systemCharlotte County Utilities, Burnt Store systemLee County

Treat the table as a starting point. Some lots in Burnt Store Lakes were built on wells and septic before lines reached them, and listings for the same street can disagree. Your utility bill, or the lack of one, tells you what you have. If there’s a well tank in the garage and a septic lid in the yard, you’re on your own system.

The Burnt Store water system

Charlotte County Utilities took over the Burnt Store service area from Florida Water Services in December 2003. The plant sits near the Charlotte and Lee County line and treats groundwater with reverse osmosis. Roughly 80 percent of the water sent through the membranes becomes drinking water. The leftover concentrate is pumped into deep injection wells about 3,000 feet down. The plant can treat up to 3.6 million gallons a day, and a 2008 boil-water notice for the system listed customers along Burnt Store Road south to the Lee County line, Burnt Store Marina included.

The county’s 2024 water quality report for this system shows chlorine as the disinfectant, at an average of 1.4 parts per million. Sodium came in at 71 parts per million, which the report puts down to saltwater intrusion and leaching from soil. Lead and copper results were well under their action levels.

What Different Water Does to Your Plumbing

RO water from the Burnt Store plant and city surface water from Shell Creek behave differently once they’re inside a house. Neither is bad. They just wear on different parts.

Reverse osmosis water

RO strips out most of the minerals, so you generally see less hard white scale on shower heads and less sediment in a tank water heater than you’d expect in Southwest Florida. The tradeoff is that very low-mineral water can be more aggressive toward metal. On older copper we look for blue-green staining at fittings and pinholes on hot lines. Most Burnt Store homes are new enough to have CPVC or PEX, which isn’t affected the same way, but the water heater’s anode rod still does its job and still wears out.

City surface water

Surface water quality shifts with rainfall. The city added reverse osmosis treatment at its plant to bring down dissolved solids during the dry season, and our main Punta Gorda page covers the city system in more detail. In PGI homes we still find scale in tankless heaters and mixing valves, plus sediment at the bottom of older tank heaters.

Private wells in Burnt Store Lakes

Well water here is a different animal: hardness, iron and sulfur smell are common complaints, and treatment is usually a softener, an iron filter or both. If you’re on a well, the pump, pressure tank and switch are yours to maintain. We repair and replace well pumps and pressure tanks, and we can help size filtration to what’s actually in your water once you’ve had it tested.

Pipes You’ll Find in a Punta Gorda Isles Canal Home

PGI is the older half of this page, and that’s where most of our repipe and slab leak work comes from. A typical original house is a single-story block home on a slab, close to the canal, with the supply and drain lines running under the floor.

  • 1960s and early 1970s houses: galvanized steel or copper supply, cast iron drains under the slab. Galvanized from this era is near the end of its life everywhere it’s still in service. It closes up with rust inside, pressure drops, and threads start to seep.
  • Mid 1970s through the early 1990s: copper became standard, and polybutylene shows up in some remodels and additions. Gray plastic pipe with crimp rings is the giveaway.
  • Rebuilds after 2004: CPVC or PEX supply and PVC drains. If the house was gutted after Hurricane Charley, it may have been replumbed then.

Mixed systems are the norm. We regularly see houses where the supply was moved to the attic years ago but the original cast iron still runs under the slab to the street. That’s why we don’t call a house “repiped” until we’ve looked at both sides, supply and drain.

If you’re buying in PGI, the pipe type also affects insurance. Many carriers ask for a four-point inspection on older homes, and polybutylene or galvanized can be a problem. Our polybutylene and 4-point inspection guide explains what inspectors look for.

Burnt Store Isles and Burnt Store Lakes: Newer Homes, Different Problems

BSI and Burnt Store Lakes have far less galvanized and cast iron, so the calls are different. They’re more about fittings, fixtures and equipment than pipe that’s rotting from age.

  • CPVC from the 1980s and 1990s gets brittle in hot attics. It can crack when someone bumps it or tightens a valve, especially at the water heater and in the garage.
  • Early PEX installs with fittings that weren’t crimped right, which usually show up as a slow drip behind a wall rather than a burst.
  • Builder-grade shutoff valves and supply lines that have never been turned since the house was built and won’t close when you need them.
  • Tankless water heaters that were never flushed, mostly on well water or in PGI.
  • Irrigation and outdoor connections on lots with a lot of exterior plumbing for pools, outdoor kitchens and boat lifts.

On a well-and-septic lot, also keep an eye on the drain field. Slow drains in every fixture plus wet, smelly ground over the field is a septic problem, not a clog, and snaking the house drain won’t fix it.

Salt Air and Outdoor Plumbing

Every house on this page is within a short distance of salt water, and most are on a canal or the harbor itself. Salt air eats exposed metal. Inside the house it’s mostly a cosmetic issue. Outside, it’s a maintenance item.

  • Brass hose bibs and their packing nuts corrode and seize. A bib that won’t shut off is usually the first sign.
  • Exposed copper at the meter, the softener loop and the pool fill line turns green and thins out over time.
  • Gas line fittings and regulators at outdoor kitchens and tankless heaters should be checked for rust. Corroded gas fittings get replaced, not painted over.
  • Mounting hardware and fasteners on wall-hung tankless heaters outside the house rust before the heater does.

Sea walls and docks aren’t plumbing, and we don’t work on them. Where the canal matters to us is storm surge, which brings us to Charley and Ian.

Charley in 2004 and Ian in 2022

Hurricane Charley came ashore at Punta Gorda on August 13, 2004, as a Category 4 storm. Its damage was mostly wind, and it led to a wave of rebuilds and partial remodels in PGI. Hurricane Ian made landfall in Southwest Florida on September 28, 2022, and this time surge and flooding were a bigger part of the story for low lots along the canals and the harbor.

The two storms left different plumbing problems behind:

  • Wind-era repairs (Charley): new roofs and drywall over old pipe. A house can look remodeled and still have original galvanized or cast iron.
  • Surge and flood damage (Ian): water heaters, softeners and well equipment in garages that sat in salt water, sand and silt in drain lines, and corroded electrical controls on equipment that seemed fine at first.
  • Rushed fixes: post-storm patch jobs on supply lines, valves and water heaters that were done fast and never permitted.

If water got into your garage during Ian, look hard at anything that sat on the floor. A gas water heater that was submerged should not just be relit. A camera run through the main drain is a reasonable step if drains have been slow since the storm. We do sewer camera inspections to see whether it’s debris we can clear or a damaged line. For storm prep before the next one, our hurricane plumbing checklist walks through shutoffs, water heaters and what to do when you get back.

Flood Rebuild Rules and Plumbing

Much of PGI, BSI and the low areas near the marina are in FEMA special flood hazard areas. Communities in the National Flood Insurance Program, including the City of Punta Gorda, Charlotte County and Lee County, enforce what’s commonly called the 50 percent rule. If repairs or improvements to a building in a flood zone reach half of the structure’s market value, the whole building has to be brought into compliance with current flood rules, which usually means elevating it or rebuilding.

That affects plumbing in a few practical ways:

  • Plumbing costs count toward the improvement total, so a large repipe combined with a kitchen and bath remodel can push a project closer to the threshold. Each office has its own way of tracking it, so ask before you plan a big job.
  • In elevated rebuilds, water heaters, softeners and other equipment generally go above the design flood elevation, and pipes run under the elevated floor need to be protected and supported.
  • Below-elevation enclosures in flood zones have limits on what can be finished or installed there, which affects where a laundry or utility sink can go.

We aren’t the ones who make substantial damage calls. That’s the building official. What we can do is give you a clear scope of the plumbing work so you or your contractor can submit it accurately.

Burnt Store Marina Condos and Villas

A lot of the housing at the marina is condos, villas and other shared-wall buildings. Plumbing in those buildings splits between the owner and the association, and the line is set by the condo documents, not by the plumber.

In general, the unit owner covers fixtures, the water heater and the supply lines that serve only their unit. Shared risers and stacks are usually the association’s. A leak in a ceiling can come from your unit, the one above, or a common pipe, and the first job is figuring out which. We work with owners, managers and associations on that. Our condo plumbing page has more on who handles what, and why water heater age matters so much in stacked units.

Part-Year Homes on the Water

Plenty of owners here spend summer somewhere else. An empty house on a canal in August has its own set of risks: a slow leak that runs for months, a washer hose that splits, dry traps that let sewer gas in, and a well pump that short-cycles every time a fitting drips.

The basics are simple. Know where your main shutoff is and make sure it works. On a well, turning off the pump breaker does the same job. Shut off or set the water heater to vacation. Put leak sensors under sinks and by the heater. Our seasonal home plumbing checklist has the full before-and-after list, so we won’t repeat it here.

If you’d rather have someone look the system over once a year, our annual plumbing maintenance plan is a yearly check-up of the house’s plumbing. Call us for the details.

Repipes, Leaks and Drains: How We Approach Them Here

Repiping

In a PGI slab home, we usually reroute new supply lines through the attic and walls rather than trenching the slab. That avoids tearing up tile floors and gets the lines out from under the house. In an elevated rebuild the route is different, under the structure with proper support. Our whole-house repiping page explains materials and what the process looks like.

Leak hunting

Start with the meter. Shut every fixture and appliance off, note the reading, and check it 30 minutes later. If it moved, there’s a leak somewhere. On a well, a pump that kicks on when nobody is using water points to the same thing. From there we narrow it down before opening anything.

Drains and sewer

In PGI the drain story is usually old cast iron under the slab: scale buildup, cracked bottoms and sags. In Burnt Store Lakes it’s more likely to be grease, wipes or a septic issue. The diagnosis is different, so the fix is too.

Nearby Areas We Also Serve

For the rest of the city, including downtown and the US 41 corridor, see our Punta Gorda plumber page. North across the Peace River, our Port Charlotte page covers that side of the harbor. For the county as a whole, go to Charlotte County plumbing. Heading south down Burnt Store Road, our Cape Coral page picks up where Burnt Store Marina ends.

Our office is at 3903 Dr Martin Luther King Jr Blvd, Suite A, in Fort Myers, and we’re open Monday to Friday, 8am to 5pm. Outside those hours we take urgent calls by phone when we can. You can reach us at (239) 518-4198 or help@homeflowfl.com.

Common Questions

Is Burnt Store Marina in Charlotte County or Lee County?

Lee County. It sits just south of the county line, with Charlotte County to the north and Cape Coral to the south. Many addresses there still use Punta Gorda mailing addresses, and water and sewer have come from the Charlotte County Utilities Burnt Store system, but building permits go through Lee County.

Is Burnt Store Isles in the City of Punta Gorda?

Yes. Burnt Store Isles and Punta Gorda Isles are both inside city limits, so plumbing permits go through the City of Punta Gorda and water comes from the city utility. Burnt Store Lakes, farther south along Burnt Store Road, is unincorporated Charlotte County.

Where does Burnt Store area water come from?

Charlotte County Utilities treats groundwater with reverse osmosis at its Burnt Store plant near the county line. The 2024 water quality report lists chlorine as the disinfectant and a sodium level of 71 parts per million, which the county attributes to saltwater intrusion and soil leaching.

Do I need a water softener in Punta Gorda Isles or Burnt Store?

Not always. RO water from the Burnt Store plant is already low in minerals, so many homes there don’t need one. City water and private wells are a different story. Get the water tested first, then decide. We install and service water softeners and filtration when the test shows a need.

My PGI house was remodeled after Hurricane Charley. Does that mean it was repiped?

Not necessarily. Many Charley repairs replaced roofs, drywall and fixtures while the original supply and drain lines stayed in place. Check under sinks and at the water heater, look at the permit history, and if you’re still unsure, we can identify what’s in the house during a visit.

Will a repipe trigger the 50 percent flood rule?

A repipe on its own rarely gets there, but plumbing costs do count toward the improvement total in a flood zone. If it’s part of a larger remodel, ask the building office for your property how they calculate it before you finalize the scope.

Can you work on my well and septic in Burnt Store Lakes?

We repair and replace well pumps, pressure tanks and the plumbing inside the house. Septic tank pumping and drain field work are handled by septic contractors, and we’ll tell you if what we find points that way.

Need a plumber?

Call (239) 518-4198 or send us a request and we’ll get back to you.

Scroll to Top