Tankless Water Heaters in Bonita Springs, FL

Leer esta página en español · Ler esta página em português

A tankless water heater in Bonita Springs depends on three local questions: your water, the fuel at your street, and where the unit can safely sit. This page covers the Bonita specifics, including Bonita Springs Utilities water, gas and propane, electric panel limits, flood elevation and city permits. Call HomeFlow Plumbing at (239) 518-4198 to talk through your house.

Three Questions That Shape Every Bonita Springs Tankless Job

Most tankless questions in Bonita Springs come down to three things before we ever talk about brands or models. Who treats your water, and how hard is it when it reaches the heater. What fuel is actually available at your house: natural gas, propane or only electric. And where the heater will sit relative to the garage floor, the vents, and the flood elevation for your lot.

Get those three answers right and the rest of the job is straightforward. Get one wrong and you end up with a unit that scales up early, a gas line that can’t keep the burner fed, or a heater mounted where the next storm can reach it. This page walks through each one for Bonita Springs specifically. For the basics of how tankless heaters work, the general pros and cons, and repair symptoms, see our main tankless water heaters page. If you’re still deciding between tank and tankless, our hard water comparison guide covers that choice in depth.

Bonita Springs Utilities Water and Your Heat Exchanger

Most homes inside the city limits, plus Estero and parts of unincorporated south Lee County, buy water from Bonita Springs Utilities, a member-owned cooperative. BSU draws from two sources. Water from the shallower Lower Tamiami Aquifer goes through lime softening. Water from the deeper, saltier Upper Floridan Aquifer goes through reverse osmosis. The two are blended before they go out to customers.

For a tankless owner, that matters in two ways. First, blended RO and lime-softened water is gentler on a heat exchanger than raw limestone groundwater, so a home on BSU water usually starts in a better place than a home on an untreated well. Second, it is still not scale-free. Hardness varies with the blend, and any mineral left in the water drops out fastest where water gets hottest, which in a tankless unit is a narrow set of passages in the heat exchanger.

Compare your water to the manual, not to a rule of thumb

Tankless manufacturers publish water quality limits, and they are specific. One major manufacturer’s installation manual lists total hardness up to 200 mg/L, chlorides up to 250 mg/L and total dissolved solids up to 500 mg/L as the limits for its units. Pull the most recent annual water quality report from your utility, find the hardness and TDS lines, and compare them to the manual for the unit you’re considering. If you’re close to or over a limit, plan on treatment before the heater goes in, not after it starts throwing scale codes.

Homes on private wells

Some Bonita Springs properties, especially larger lots outside the utility’s main grid, still run on private wells. Well water here has not been through lime softening or RO, so hardness and iron can be well above what BSU customers see. A well home should have a water test before a tankless purchase, and in most cases a softener or scale-control system ahead of the heater. We cover options on our water softeners and filtration page, and wells themselves on our well pump page.

Flush and Descale Intervals on Bonita Water

Manufacturers don’t give one flush interval for everybody. One major brand’s manual lets the installer set a service reminder at six months, one year or two years, and says plainly that hard-water areas may need a more frequent flushing schedule. Your interval should come from your water, your temperature setting and how much hot water the house uses.

Here is how we’d set the schedule for typical Bonita situations:

SituationStarting flush intervalWhy
BSU water, setpoint near 120°F, two to three peopleOnce a yearTreated water and moderate use keep scaling slow
BSU water, large household or setpoint above 125°FEvery six to nine monthsMore gallons through the heat exchanger and hotter water both speed up scale
Private well with a working softenerOnce a year, plus a check of the softenerSoftened water protects the unit only while the softener is regenerating properly
Private well, untreatedEvery six months at minimumHard, untreated well water can scale a heat exchanger quickly; treatment is the real fix
Seasonal home, used part of the yearOnce a year, at the start of the seasonLow run hours, but standing water and sediment still collect in the inlet screen

Use the first flush as a measuring stick. If the descaling solution comes out cloudy with visible grit, or the inlet screen is packed, shorten the interval. If it runs clear and the screen is clean, the starting interval is probably right.

Signs you’re overdue

  • Water temperature swings during a shower even though nobody else is running water
  • The unit takes longer to reach temperature than it used to
  • Scale or overheating error codes, or a maintenance reminder on the display
  • A whistling or rushing sound from the heat exchanger during heavy use
  • Lower hot water flow at every fixture, not just one

Keep a simple log taped inside the garage cabinet or utility closet: the date of each flush and what came out. Warranty claims on heat exchangers often turn on maintenance history, and a written log is easy proof. Our annual plumbing maintenance plan is a yearly check-up of the whole plumbing system, and it’s a natural time to look at the water heater too.

Natural Gas, Propane or Electric: What Is Actually at Your Street

Natural gas in Lee and Collier counties comes from Peoples Gas, which runs a Fort Myers and Naples service area. That doesn’t mean every Bonita street has a main. Gas service follows where pipe has been laid, so one community can be fully piped while the neighborhood across the road is all-electric. Plenty of older single-family homes and many condo buildings in Bonita were built without gas.

How to tell what you have

  • Look for a gas meter on the exterior wall, usually near the garage or the side yard
  • Check whether the range, dryer, pool heater or generator already runs on gas
  • Look for a buried or above-ground propane tank, often in the side or back yard
  • If none of those exist, ask the gas utility whether a main runs past your address and what a new service would involve

If you already have natural gas

A whole-house gas tankless is usually the strongest option, but the existing piping was sized for whatever the house had before. A typical tank heater burns a fraction of what a whole-house tankless burns at full fire, so the line that fed the old tank is often too small. We check the gas meter capacity, measure the pipe run, and add up every gas appliance before choosing a unit. Upsizing or rerouting gas pipe is gas line work, and it’s often the biggest variable in a conversion.

If you’re on propane

Propane tankless works well, but the tank and regulator have to keep up with the burner on the coldest morning with every shower running. A small tank that was sized for a range or a fireplace may not supply a whole-house unit. Talk to your propane supplier about tank size and delivery, and confirm your HOA allows the tank where it needs to sit. The heater itself must be the propane version, or be properly converted per the manufacturer.

If gas isn’t available

Electric tankless is the remaining option, and the question shifts to your electrical panel. That’s next.

Electric Tankless and Your Panel: The Published Numbers

Electric tankless units pull a large current, and the manufacturer’s spec sheet tells you exactly how much. Here are the published figures for two sizes of one widely sold electric line, including flow at Florida groundwater temperatures to a 105°F setpoint:

Published spec18 kW model27 kW model
Total amperage at 240V75 amps112.5 amps
Breakers requiredTwo 40-amp double-poleThree 40-amp double-pole
Wire size8 AWG copper per circuit8 AWG copper per circuit
Recommended service panel150 amps200 amps
Flow with 72°F incoming water3.7 GPM5.6 GPM
Flow with 77°F incoming water4.4 GPM6.6 GPM

Source: the manufacturer’s published spec sheet for those two models. Other brands are similar but not identical, so always check the sheet for the exact unit.

When the panel is the deciding factor

  • If the house has 100-amp service, a whole-house electric unit is generally off the table without a service upgrade
  • If the panel has no room for two or three more double-pole breakers, a subpanel or panel replacement comes first
  • If the house already runs central air, an electric range, a dryer and a pool pump on a 150-amp service, a load calculation decides whether an 18 kW unit fits
  • If the panel is an older model with a known reliability or insurance problem, many owners replace it during the same project

Panel and service work belongs to a licensed electrician and goes under its own electrical permit, and an upgrade may involve the power company if the service size changes. We coordinate the plumbing side around the electrical work so the heater, piping and circuits are ready for inspection together. When a panel upgrade isn’t practical, a smaller point-of-use unit at one bathroom or a heat pump water heater can be the better answer.

Sizing for Bonita Springs Inlet Temperatures

Florida groundwater runs around 72°F, and the cold water entering a Bonita home sits near that most of the year. Tankless sizing is all about the temperature rise: a 120°F setpoint from 72°F incoming water is a 48-degree rise, which most units handle at a much higher flow than the same unit would deliver in a northern winter. That’s why sizing charts written for cold climates tend to oversize units for Southwest Florida.

Two cautions keep us from cutting it too close. Incoming temperature does drift a few degrees with the season, especially after a cold snap or where a supply line runs shallow, so we size for the cooler end of the year rather than August. And long sun-heated runs of pipe can make the cold side warmer in summer than the ground actually is, which can fool a homeowner into thinking a marginal unit is fine.

Count the fixtures you really use at once

Make a list of what runs together on a busy morning. A typical Bonita pool home might have two showers going, a dishwasher and a washing machine. Add the rated flow of each showerhead (look for the GPM stamped on it), then compare that total to the manufacturer’s flow chart at a 45 to 50 degree rise. Big soaking tubs and multi-head showers are the fixtures that break a sizing plan, because they want a high flow at full temperature for several minutes.

  • Two-bedroom condo, one or two people: often a single smaller unit or a point-of-use setup works
  • Three-bedroom, two-bath single-family home: a mid-size whole-house gas unit or a larger electric unit if the panel allows
  • Four-bath home with a pool bath and a soaking tub: a large gas unit, or two units linked together, sized to the busiest real-world hour

Venting Rules for Gas Tankless Units

A gas tankless unit is either vented through a wall or roof (indoor models) or mounted outside with an integral vent (outdoor models). Either way, the vent termination has minimum clearances set by the manufacturer and the Florida fuel gas code, and inspectors check them.

As an example, one major manufacturer’s manual lists these clearances for its indoor direct-vent units in the US: 12 inches from a window or door that can be opened, 12 inches above grade or a deck, 12 inches from another appliance’s air intake, and 3 feet above any mechanical air supply inlet within 10 feet horizontally. For its outdoor units the same manual calls for 4 feet below or beside an operable window or door and 1 foot above it.

What that means on a Bonita house

  • Lanai cages and covered patios: the vent can’t discharge into an enclosed lanai or under a covered area where exhaust collects
  • Windows near the garage: many garages sit next to a bedroom window, which limits where an outdoor unit can hang
  • AC equipment and fresh air intakes: keep exhaust away from the air handler intake and any fresh air duct
  • Condensing units: these vent in PVC-type pipe and produce acidic condensate that needs a drain path, usually with a neutralizer
  • Replacing an old tank: the existing metal flue from a tank heater generally can’t be reused for a tankless; the unit needs the vent material its manual specifies

Outdoor tankless units are popular here because they skip the indoor vent run entirely. They still need clearances from openings, a spot where sprinklers won’t hit them constantly, and protection from storm debris where possible.

Garage Installs in Bonita Springs

In most Bonita single-family homes, the water heater lives in the garage, and a tankless conversion usually keeps it there while freeing up floor space. Garages come with their own code points.

Under the residential code, a gas appliance in a garage generally has to have its ignition source at least 18 inches above the floor, because gasoline vapor sits low. Sealed-combustion, direct-vent appliances that take all combustion air from outside are treated differently, and electric units have no open ignition source. A wall-mounted tankless typically sits well above 18 inches anyway, but we confirm it against the specific model and its listing rather than assume.

Other garage details we plan for

  • Vehicle protection: a unit or its piping in the path of a car needs to be out of reach or behind a barrier
  • Heat: Bonita garages get hot in summer, so we check the unit’s ambient temperature range and keep it away from direct sun through a window
  • Room for treatment: leave wall space for a softener or scale-control cartridge and its service valves ahead of the heater
  • Drainage: the relief valve discharge and any condensate need an approved place to go, not just the garage floor
  • Isolation valves: service valves on the hot and cold lines make every future flush a short job

Flood Elevation and Storm Exposure

The Imperial River runs through downtown Bonita Springs, and floodwater from it and from surge on the coast has damaged garages and ground floors in recent storms. Our Bonita Springs plumber page covers that history. For a tankless install, the practical question is how high the unit and its controls sit compared to the flood elevation for your lot.

What the city’s flood rules say

In the City of Bonita Springs, the Building Official is the designated Floodplain Administrator. The city’s flood hazard ordinance requires mechanical, plumbing and electrical systems in new development to be above the design flood elevation or meet a specific engineering standard. Substantial improvement is measured cumulatively: work over a five-year period that adds up to 50 percent or more of the building’s market value triggers full flood compliance for the whole structure. A water heater replacement alone rarely gets close to that, but it can be one piece of a larger remodel that does.

State floodplain guidance issued in 2026 says that flood-damaged exterior equipment that gets replaced, rather than cleaned and put back in service, generally needs to meet flood elevation requirements, and that partial elevation meets the intent where full elevation is hard to achieve. That guidance also flags a proposed code change that would set the height at the first floor level or 4 feet above grade, whichever is higher. Your building official makes the final call for a specific address.

Practical steps whether or not the rules require them

  • Mount the unit as high on the wall as service access allows, above any water line from past storms
  • Keep the electrical disconnect and any control boards above that line too
  • Before relighting or powering a unit that sat in floodwater, have it inspected; water can damage controls, burners and wiring in ways you can’t see
  • Photograph the heater, its data plate and the water line before cleanup for your insurance claim

Our hurricane plumbing checklist covers what to do with the water heater and gas supply before and after a storm.

Permits: City of Bonita Springs, Lee County or Estero

A Bonita Springs mailing address doesn’t tell you which building department handles your permit. The City of Bonita Springs runs its own Community Development building division. Properties with a Bonita address that sit outside the city limits fall under Lee County’s building department in unincorporated Lee. And the Village of Estero to the north issues its own permits. Check your property record to see which jurisdiction you’re in before anyone schedules work.

The city requires a permit for water heater replacement, and a switch from tank to tankless adds more items for the inspector to check. The city’s Community Development office can be reached at (239) 444-6150. It has a Permit Portal, but as of this writing the city says only Trade Mechanical permits can be applied for online, and other permit types and licenses still have to be submitted in person. The city also adopted a new building permit fee schedule effective January 1, 2026, so check the current schedule rather than an old fee sheet.

What usually needs a permit on a tankless conversion

  • Plumbing: the water heater itself, water connections, relief valve discharge and condensate
  • Gas: new or upsized gas piping, which is typically pressure tested before the inspector signs off
  • Electrical: new circuits for an electric unit, or a receptacle for a gas unit’s controls and igniter, by an electrician under their own permit
  • Venting: the vent route and termination clearances, inspected against the manufacturer’s manual

Keep the final inspection record with your house papers. Buyers, insurers and associations ask for it, and an unpermitted water heater can come up on a 4-point inspection when you insure or sell the house.

Whole-House or Point-of-Use in a Bonita Home

A whole-house unit replaces the tank and serves every fixture. Point-of-use units are small heaters installed near one fixture or one group of fixtures. In Bonita homes, a few layouts make the choice clearer.

LayoutUsually the better fitReason
Single-story home with the heater at one end and the master bath at the otherWhole-house unit plus recirculation, or a point-of-use unit at the far bathLong runs mean a long wait for hot water even with a strong heater
Pool bath or outdoor shower off the lanaiPoint-of-use unitAvoids running a hot line across the house for occasional use
Outdoor kitchen sinkPoint-of-use unitSmall demand far from the main heater
Condo with no gas and a limited panelPoint-of-use or a smaller electric unitWhole-house electric may exceed the unit’s electrical capacity
Guest suite or detached casitaSeparate small unitIsolates use and avoids a long underground hot line

Mixing the two is common: one whole-house gas unit for the main living area and a small electric unit at a remote bath. Point-of-use electric units still need their own dedicated circuit, so check the panel before buying one online.

Condos, High-Rises and HOA Communities

Bonita Springs has a large share of condos, mid-rise and high-rise buildings, and gated communities, and each adds a layer of approval before a water heater changes.

  • Board approval: most associations require written approval, the contractor’s insurance certificate and sometimes the permit before work starts
  • Gas: many condo buildings have no gas service to individual units, which makes electric or point-of-use the only tankless options
  • Electrical capacity: unit panels in older buildings may be too small for a whole-house electric tankless, and the building’s riser may limit upgrades
  • Location and leak control: associations often require a drain pan, a leak detector or an automatic shutoff valve, and may dictate the closet the heater must stay in
  • Work rules: elevator reservations, work hours and parking for service vehicles are set by the association
  • Exterior changes: a new wall vent or outdoor unit on a building’s exterior generally needs separate architectural approval

Read your condo documents before you shop for a unit, because the rules may decide the type for you. Our condo plumbing page covers how we work in associations, and property managers can see our HOA and property manager plumbing page.

What a Tankless Installation Looks Like, Step by Step

Once the fuel, location and permit questions are settled, the install itself follows a predictable order:

  • Site visit: we confirm the water source, gas or electric capacity, vent route, mounting wall and flood elevation
  • Unit selection: sized to your real peak demand at Florida inlet temperatures, and checked against your water quality and the manufacturer’s limits
  • Permits: applied for with the right jurisdiction, with gas and electrical work coordinated
  • Removal: the old tank is drained, disconnected and hauled off; the old flue is capped or removed as required
  • Mounting and piping: the unit goes on the wall with isolation valves, a relief valve and its discharge, and any treatment equipment ahead of it
  • Gas or electric: gas piping is installed or upsized and pressure tested, or the electrician completes the dedicated circuits
  • Venting and condensate: the vent is run and terminated at the required clearances; condensing units get a drain and neutralizer
  • Startup: the unit is fired, the setpoint and any recirculation schedule set, flow and temperature checked at the fixtures
  • Inspection: the inspector checks the work, and you get the startup settings and the first flush date

Before We Arrive: A Homeowner Checklist

A little preparation saves time on the first visit and helps the estimate match the real job.

  • Find your most recent water utility bill or annual water quality report, or a well water test if you have one
  • Note whether you have a gas meter, a propane tank or neither
  • Take a photo of your electrical panel’s main breaker and the labels on each breaker
  • Clear about 3 feet around the current water heater and the wall where a tankless might go
  • List the fixtures your household runs at the same time on a busy morning
  • If you’re in a condo or HOA, get the association’s water heater rules and approval form
  • Know whether your home is inside the City of Bonita Springs, unincorporated Lee County or Estero
  • If the garage has flooded before, note how high the water reached

If your current tank is leaking now, shut the cold supply valve on top of the tank and turn off the gas or the breaker. Our water heaters page covers tank replacement and repairs if a straight swap makes more sense for your situation. Call us at (239) 518-4198, Monday to Friday, 8am to 5pm. We speak English, Spanish and Portuguese.

Common Questions

Is natural gas available in my Bonita Springs neighborhood?

It depends on the street. Peoples Gas serves the Fort Myers and Naples area, but gas mains only run where pipe has been laid, so some communities have gas and nearby ones don’t. Look for a gas meter or other gas appliances, and if you have neither, ask the gas utility whether a main runs past your address. Propane is the alternative for many homes without a main.

Does Bonita Springs Utilities water need a softener for a tankless heater?

Not always. BSU blends reverse osmosis water with lime-softened water, which is easier on a heat exchanger than raw groundwater. Compare the hardness and TDS figures in the utility’s annual water quality report to the limits in your heater’s manual. If you’re near the limit, keep a high setpoint, or use a lot of hot water, scale control is worth adding.

How often should I flush a tankless heater in Bonita Springs?

On BSU water with a normal household and a setpoint near 120°F, once a year is a reasonable starting point. Shorten it for big households, hotter setpoints or private well water. Use what comes out during the first flush to adjust the interval.

Can my 150-amp panel handle an electric tankless?

Possibly, for a smaller unit. One manufacturer’s published specs call for a 150-amp panel for its 18 kW model, which draws 75 amps on two 40-amp breakers, and a 200-amp panel for its 27 kW model at 112.5 amps. Whether your panel works depends on a load calculation that includes your AC, range, dryer and pool equipment.

Who issues the permit if my address says Bonita Springs but I’m not sure I’m in the city?

Check your property record. Inside city limits, the City of Bonita Springs Community Development division issues the permit. Outside city limits in unincorporated Lee County, it’s Lee County. Properties in the Village of Estero go through Estero’s building department.

Does a tankless heater in my garage have to be raised off the floor?

Gas appliances in a garage generally need their ignition source at least 18 inches above the floor unless they’re a sealed-combustion type that draws all its air from outside. Wall-mounted tankless units usually sit well above that. Separately, if your lot is in a flood zone, mounting higher than the minimum is a good idea for storm protection.

Can I put a tankless water heater in my Bonita Springs condo?

Often yes, but the association decides. Many condo buildings have no gas, so it would be electric or point-of-use, and the unit’s panel has to have the capacity. Get the association’s water heater rules and written approval before you buy anything.

My tankless sat in floodwater. Can I just turn it back on?

No. Have it inspected before restoring gas or power. Floodwater can damage controls, burners and wiring, and some of that damage is not visible from the outside. If you do replace it, check with the building department about elevation requirements for replaced equipment.

Why HomeFlow

  • One company for service calls, remodels and new construction, so you’re not lining up a different plumber for each job.
  • We work in Lee, Charlotte and Collier Counties and know the pipe, water and slab issues that come with homes here.
  • Call (239) 518-4198 or send a request online. Tell us what’s going on and where, and we’ll take it from there.

Need a plumber?

Call (239) 518-4198 or send us a request and we’ll get back to you.

Scroll to Top