Slab Leak Detection and Repair in Bonita Springs, FL

Leer esta página en español · Ler esta página em português

Bonita Springs grew mostly from the 1980s on, and many homes from that era have copper water lines buried under the slab. We find and repair those leaks with pressure testing, acoustic listening, thermal imaging and tracer gas. Call (239) 518-4198 to set up detection.

Who This Page Is For

This page is for Bonita Springs homeowners, landlords and condo owners who think water is escaping from a pipe buried under their concrete floor. It covers the local side of the job: how to use your Bonita Springs Utilities meter and account data to build a case, which office issues the permit for your address, what the age of Bonita’s housing tells us about the pipe under your floor, and how we pick a detection method and a repair route for homes here.

If you are not yet sure there is a slab leak, start with our guide to slab leak signs in Florida homes. For the general repair options in every county we serve, see slab leak repair. This page goes further for Bonita Springs specifically.

Bonita Springs Utilities: What the Utility Covers and What You Cover

Most homes in Bonita Springs get water from Bonita Springs Utilities (BSU), the member-owned cooperative that also serves Estero and unincorporated South Lee County. For a slab leak, the useful parts of BSU are its ownership rules and its usage data.

The ownership line matters the moment you suspect a leak. BSU states that it maintains the water pipes up to and including the backflow prevention device on your water service, and the sewer line up to your sewer cleanout near the property line. Everything on your side of those points, including the pipe running under your slab, irrigation and pool plumbing, is the property owner’s responsibility to maintain and repair.

BSU also says to call its Customer Service line at 239-992-0711 before calling a plumber if you think the meter itself is malfunctioning. That is a sensible first call when the bill jumps but nothing in the house seems wrong. If the utility confirms the meter is reading correctly and the usage is real, the leak is almost always on the private side, and that is where we come in.

Use Your BSU Usage Data Before Anyone Cuts Concrete

BSU offers an online portal called SpryEngage for members with advanced metering (AMI) service. The utility describes it as a way to view and track water use, review history, and check for and resolve leaks. It can send notifications for high use, bill forecasts and unplanned use.

For a suspected slab leak, this data is more useful than a single high bill. A buried pressure line leaks around the clock. That shows up as usage that never drops to zero, even overnight when nobody is running water. An irrigation problem tends to show up on the days and hours the timer runs. A running toilet often looks like steady use too, which is why we want toilets ruled out first.

What to pull from your account before you call us

  • Hourly or daily usage for the last 30 to 60 days, if your account shows it
  • The date the baseline started climbing, which helps with insurance timing later
  • Any unplanned-use or high-use alerts you received and when
  • Last year’s usage for the same months, since seasonal residents and winter guests change the picture

Bring this to the visit or email it to help@homeflowfl.com. It shortens the detection work because it tells us whether the loss is constant (pressure line), timed (irrigation) or intermittent (fixtures).

The Meter Test, Step by Step

A meter test is the cheapest piece of evidence you can collect. BSU’s own leak guidance points members to the meter and to a toilet dye check. Here is the full sequence we ask Bonita homeowners to run before a detection visit.

  • Rule out toilets first. Put a few drops of food coloring in each toilet tank and do not flush. BSU says that if color shows in the bowl in about 15 minutes, the flapper is likely leaking. Fix that before going further.
  • Turn off every water user. Faucets, showers, the dishwasher, the washing machine, the ice maker and the irrigation controller. Set the pool autofill or water softener to off or bypass if you have one.
  • Read the meter. Note the full reading and watch the small leak indicator or low-flow dial for several minutes. Take a photo with a timestamp.
  • Wait one to two hours with nothing running, then read it again. Any movement means water is leaving somewhere.
  • Close the main shutoff at the house and watch the meter again. If it stops, the leak is inside the house side of the valve, which is where slab leaks live. If it keeps moving with the house valve closed, the loss is between the meter and the house, which points to the yard service line or irrigation instead.
  • Write it all down. Readings, times, and what was on or off. This record helps us and it helps your insurer.

If you are not sure where your house shutoff is, our main water shutoff guide walks through the usual locations in Southwest Florida homes. A meter that moves with the main closed is a water line repair question, not a slab question.

Why Bonita’s Housing Age Points to Copper Under the Slab

As our Bonita Springs plumber page explains, most of the city was built between the 1980s and the mid-2000s. Census counts went from about 13,600 residents in 1990 to 53,644 in 2020. For slab leaks, the question is what was buried under the floor during that boom.

Homes in Southwest Florida from those decades were built slab-on-grade, and many had their water supply lines run as soft copper in the ground before the concrete was poured. Those lines are now 20 to 40 years old. Copper does not fail on a calendar, but age plus soil contact plus decades of thermal cycling on the hot side is the combination that produces pinholes under a slab.

Many homes from the same years used polybutylene or CPVC above the slab for the branch lines to fixtures, and some have already been repiped overhead. A house can have plastic in the attic and original copper in the ground at the same time. The first thing we do at a Bonita visit is figure out which you have. The year built on your property record, the pipe material visible at the water heater and under sinks, and whether pipes come up out of the floor or drop down from the ceiling tell us a lot before any equipment comes out.

Bonita’s gated golf and lakefront communities often share one builder and one construction window, so homes on the same street tend to have the same pipe, laid the same way, at the same time. If neighbors have already had slab leaks, treat that as a real data point about your own pipe.

Water Table, Soil and Storm Flooding in Bonita

Much of Lee County sits on sandy soil with a high seasonal water table. Lee County tracks this with a wet season high water table map built from roughly 190 monitoring wells. In Bonita, that wet-season groundwater matters for two reasons.

First, it changes what a leak looks like. In dry sand, leaking water can drain away under the slab for a long time without surfacing. When groundwater is high, the same leak can push moisture up sooner, which shows as damp grout, lifting floors or baseboard staining. A leak that seemed to appear suddenly in summer may have been running for months.

Second, it affects detection. Tracer gas moves upward through dry sand far faster than through wet soil. One equipment maker’s application notes put gas travel at 1 meter depth at about 20 minutes in dry sand and about 4 hours in wet soil, with concrete adding several hours more. Wet ground does not stop the method. It does change how long we wait and how we read the results.

Hurricane Ian and earlier floods

Ian’s surge in 2022 put water inside homes in areas like Bonita Shores, and the Imperial River kept rising for days afterward, following Irma’s flooding in 2017. Our Bonita Springs page covers storm effects on drains and water heaters. Under the slab, the effect is different.

Floodwater does not usually break a pressure pipe under the slab by itself. What it does is change the conditions around the pipe, soak the fill, and lead to floors being torn out and replaced. If your floor was replaced after Ian, ask whether anyone looked at the pipe while the slab surface was exposed. If a leak shows up now under that new floor, photos from the flood repair can help us map where pipes run. Our hurricane plumbing checklist covers storm prep for the rest of the system.

How We Find the Leak: Four Methods and When Each Fits

No single tool finds every slab leak. We combine methods, and the order depends on what the meter test showed and what the floor is made of. Our leak detection page covers the service in general. Here is how each method plays out in a typical Bonita slab home.

MethodWhat it doesBest fit in Bonita homesLimits
Pressure isolation testSeparates hot, cold and individual branches, then watches each for pressure lossFirst step on almost every job. Tells us which line is leaking before we search for whereConfirms a leak on a branch but does not locate it on the floor
Acoustic listeningGround microphones pick up the sound of water escaping a pressurized pipeTile over slab, where sound carries well; leaks in open areas of the floorBackground noise from pool pumps, AC and traffic; thick padding or carpet muffles it
Thermal imagingInfrared camera shows temperature patterns on the floor surfaceHot-side leaks, which warm the floor above themLittle help on cold lines; rugs and furniture block the view; sun on floors skews readings
Tracer gasLine is filled with a 95% nitrogen, 5% hydrogen mix; a sensor finds where gas rises through the floorQuiet leaks that acoustic cannot hear, cold-line leaks, and confirming a pinpointSlower through wet soil and concrete; usually needs the line drained first

On a typical visit, we isolate the lines, confirm which side is losing pressure, trace the likely pipe path from where it enters the slab to the fixtures it feeds, and then listen, scan or gas-test along that path. We mark the floor where the evidence agrees. Two methods pointing at the same spot is a lot more reliable than one.

Choosing a Repair for a Bonita Home

Once the leak is pinned down, there are three ways to fix it: open the slab at the leak, abandon the buried pipe and reroute overhead, or repipe the house. We explain the general version on our main slab leak repair page. Locally, these are the rules of thumb we use.

Open the slab when

  • This is the first leak in the house and pressure tests on the other branches are clean
  • The leak is in a utility room, garage, closet or an area with spare or easy-to-match flooring
  • The leak is on a cold line feeding several fixtures, where a reroute would be long and complicated

Reroute through the attic or walls when

  • The leak sits under large-format tile that cannot be matched, or under a kitchen island or built-in cabinets
  • Only one branch is affected, often a hot run from the water heater to a bathroom or kitchen
  • The attic has room to run pipe with proper insulation and support, which matters in Bonita summer heat

Repipe when

  • This is the second or third slab leak, or the tests found more than one weak branch
  • The house is in a community where neighboring homes of the same age are already leaking
  • You plan to stay long enough that one planned project beats repeated emergency calls
  • Your insurer is asking about the age of your plumbing at renewal

For a full replacement, see whole-house repiping, and for material choices, our comparison of PEX vs copper repiping in Florida. The slab leak repair cost factors page explains what makes each route bigger or smaller.

Permits: City of Bonita Springs, Lee County or the Village of Estero

The Florida Building Code lets a plumber stop a leak in a water pipe without a permit. The same section says that if a concealed water pipe becomes defective and has to be removed and replaced with new material, that work counts as new work, and a permit and inspection are required. Cutting out a failed section under a slab and splicing in new pipe often lands on the permit side of that line. Reroutes and repipes do too.

Which office issues that permit depends on where the property actually sits, not on the mailing address. A Bonita Springs mailing address does not prove a home is inside city limits. Parts of the area carry Bonita Springs or Estero addresses but are in unincorporated Lee County, and the Village of Estero covers parts of several ZIP codes that predate its 2014 incorporation.

How to confirm your jurisdiction

  • Check your property tax bill. Homes inside a city or village show an extra line for that municipality
  • Check your voter registration card. A blank city field generally means unincorporated Lee County
  • Look the address up in Lee County’s online resident information tool
  • Ask the City of Bonita Springs Community Development Department. The city lists (239) 444-6166 for zoning questions and (239) 444-6150 for flood and permit contacts

We confirm jurisdiction before we pull the permit, so you do not need to sort this out alone. If your address is in Estero, our Estero plumber page covers that area.

Flood Zones and the 50 Percent Rule

Many Bonita homes sit in Special Flood Hazard Areas. The City’s post-storm permitting guide says all work within those areas needs a permit and that damaged homes in flood zones may be assessed for substantial damage before permitting. When the total of repairs and improvements reaches 50 percent of the building’s value, the City says the building has to be brought into full compliance with current flood rules. Building values come from the Lee County Property Appraiser, and owners can submit a private appraisal if they disagree.

A slab leak repair alone is rarely large enough to approach that line. It can matter when the leak repair is part of a bigger project, such as flood recovery work or a remodel where floors, kitchen and baths are all being replaced. If you are planning a combined project, raise the 50 percent question with the city early, and tell us about the rest of the scope so we can plan the plumbing around it.

Insurance: Access Costs, Seepage Exclusions and Deadlines

We are not adjusters and we cannot tell you what your policy pays. We can tell you the issues that come up most often with Florida slab leak claims, so you ask the right questions.

Many Florida homeowners policies treat the failed pipe as a maintenance item and do not pay to replace it. Some policies do cover the cost of tearing out and replacing parts of the building to reach the pipe, often called tear-out or access coverage, plus resulting water damage. The catch is the exclusion for constant or repeated seepage or leakage. In State Farm Florida v. Feltes (2024), a Florida appeals court held that this kind of exclusion barred coverage for access to a leaking drain line under a slab, reasoning that a leak can be periodic and still count as repeated.

Timing also matters. Under Florida Statute 627.70132, notice of a property insurance claim for loss caused by any peril has to be given to the insurer within one year after the date of loss. Your usage history from BSU can help establish when the leak started.

  • Call your carrier before demolition, and ask specifically about access or tear-out coverage
  • Save meter test records, BSU usage graphs and alert emails
  • Photograph flooring, baseboards and the marked leak spot before anything is opened
  • Ask us for a written scope that separates finding the leak, opening the floor, fixing the pipe and closing the floor
  • Keep removed pipe sections if your adjuster wants to see them

Condos, Villas and Coach Homes in Bonita

Bonita has a lot of attached housing: coach homes, villas and low-rise condos inside golf and lakefront communities. A slab leak in a unit on the ground floor can involve a pipe that serves only that unit, a pipe shared with a neighbor, or a pipe the association treats as a common element. Before anyone opens a floor, the association’s documents decide who authorizes and pays for the work.

Ask the manager whether cutting a slab needs written approval, whether there are work-hour limits, and whether water to the building has to be shut off. Some communities also restrict noise and dust during season. Our condo plumbing page covers working inside associations in more detail.

Preparing Your Home for Detection and Repair Day

A little preparation makes detection more accurate and the repair cleaner. Use this checklist the day before we arrive.

  • Run the meter test and have your readings ready
  • Clear rugs, furniture and boxes from the rooms between the water heater, kitchen and bathrooms
  • Turn off the pool pump, fountains and loud appliances during the visit so acoustic listening is not drowned out
  • Find the main shutoff and the water heater shutoff and make sure both turn
  • Locate any spare tile, grout color or flooring from the original install or a past remodel
  • Get house plans or old remodel photos if you have them, since they show where pipes were laid
  • Clear a path to the attic hatch if a reroute is possible
  • Plan for pets and family members to be away from a work area with concrete dust
  • For condos, get written approval from the association before the repair date

On the repair day itself, water will be off for part of the work. Fill a few containers for drinking and flushing. After the fix, we pressure test the new section before anything is closed up and recheck the meter with everything off.

Talk to HomeFlow About a Bonita Springs Slab Leak

HomeFlow Plumbing is an insured residential and commercial plumbing contractor based in Fort Myers, serving Bonita Springs and the rest of Lee, Collier and Charlotte Counties. Our office is at 3903 Dr Martin Luther King Jr Blvd, Suite A, Fort Myers, FL 33916, open Monday to Friday, 8am to 5pm. Outside those hours we take urgent calls by phone when we can. Our staff speak English, Spanish and Portuguese.

Call (239) 518-4198, email help@homeflowfl.com, or use our contact page. For everything else we do locally, see our Bonita Springs service page. If you want a yearly look at the rest of your plumbing after the leak is fixed, ask about our annual maintenance plan.

Common Questions

Is Bonita Springs Utilities responsible for a leak under my slab?

No. BSU says it maintains the water pipes up to and including the backflow prevention device on your service. The pipe under your house is private plumbing, so finding and repairing it is the owner’s job. If you think the meter itself is wrong, BSU asks you to call its Customer Service line at 239-992-0711 first.

My BSU meter keeps moving with the house shutoff closed. Is that a slab leak?

Probably not. If the meter moves with the main valve at the house closed, the water is leaving between the meter and the house, which points to the yard service line or irrigation. A slab leak shows up as meter movement that stops when the house valve is closed.

Can SpryEngage alerts tell me I have a slab leak?

They can tell you something is using water when it should not be. BSU says the portal shows usage history and can notify you about high and unplanned use. A pattern of use that never drops to zero overnight is a strong reason to run a meter test and book detection. It does not tell you where the leak is.

Does a slab leak repair in Bonita Springs need a permit?

Often, yes. The Florida Building Code allows stopping a leak without a permit, but replacing a defective concealed water pipe with new material is treated as new work that needs a permit and inspection. Reroutes and repipes need permits too. Which office issues it depends on whether your property is in the City of Bonita Springs, the Village of Estero or unincorporated Lee County.

My address says Bonita Springs. Doesn’t that mean the city handles the permit?

Not necessarily. Mailing addresses and ZIP codes do not follow city limits. Check your tax bill for a municipal line, your voter card for a city name, or look the address up with Lee County. We confirm jurisdiction before pulling a permit.

Can Hurricane Ian flooding cause a slab leak now?

Floodwater rarely breaks a pressurized pipe under a slab by itself. It does saturate the fill under the house and often led to floors being replaced. If you have a leak now under flooring replaced after Ian, photos from that work can help map where pipes run. Age and pipe material are still the main drivers.

Does tracer gas work in Bonita’s wet soil?

Yes, but it is slower. The gas mix of 95 percent nitrogen and 5 percent hydrogen rises through dry sand much faster than through wet soil, and concrete adds hours. During the wet season we allow more time and confirm with a second method where we can.

What should I tell my insurer about a slab leak?

Report it promptly, ask about tear-out or access coverage, and share your meter readings and usage history. Florida law requires notice of a property claim within one year after the date of loss. Many policies exclude repeated seepage, so the timeline you document matters.

Why HomeFlow

  • One company for service calls, remodels and new construction, so you’re not lining up a different plumber for each job.
  • We work in Lee, Charlotte and Collier Counties and know the pipe, water and slab issues that come with homes here.
  • Call (239) 518-4198 or send a request online. Tell us what’s going on and where, and we’ll take it from there.

Need a plumber?

Call (239) 518-4198 or send us a request and we’ll get back to you.

Scroll to Top